SMD screen price in Pakistan
There is no honest flat rate for an SMD screen in Pakistan. The same size of wall can differ several times over in price, and the reasons are specific and checkable. This page sets them out, then gives you a figure for your own site rather than a number built to win a phone call.
What decides the number
8 things move the price of an SMD screen. A quotation that does not state all of them cannot be compared with one that does.
- Pixel pitch
- The single largest driver. Halving the pitch roughly quadruples the number of LEDs in the same square foot, so two screens of identical size can differ several times over in cost. Specify pitch from viewing distance, not from a spec sheet.
- Screen area
- Mid-range installations are priced per square foot, so area moves the total more than any other single dimension. A wall two feet taller is not a small change, and it is worth sizing the screen to the viewing distance rather than to the wall.
- Indoor or outdoor
- Outdoor cabinets are sealed to IP65, run several times brighter and carry heavier power and heat handling. The same pitch costs more outdoors, and an indoor panel put outside fails quickly.
- Structure
- Wall-mounted, ground-supported, cantilevered off a facade or rigged from a roof. Steel, fabrication and access frequently cost more than people expect relative to the screen.
- Processing and control
- Sending and receiving cards, the processor tier, and whether the installation needs redundancy or a backup path for a screen that cannot go dark.
- Power and protection
- Distribution, surge protection and stabilisation. In Pakistani conditions this is what decides whether the screen survives its first year, and it is the first thing a cheap quotation removes.
- Site access
- Height, crane or hoist requirements, road or lane closure, and whether the work has to happen at night. Access can change the schedule and the cost of the same screen.
- Service and warranty
- Spare module holding, response time and who actually attends when a module fails. A warranty is only worth the engineer behind it.
Per square foot, or per solution
- Mid-range installations
- Quoted per square foot of screen, with structure, power protection and commissioning itemised separately so you can see what is screen and what is everything else. It makes two quotations genuinely comparable.
- High-end installations
- Quoted as a single price for the whole solution rather than a rate per foot. At this level the screen is the smaller part of the engineering, structure, redundancy, processing and integration are specified as one system, and pricing them per foot would misrepresent the job.
- What is always separate
- Travel, access and any civil or steel work are priced up front rather than appearing later. A quotation that hides them is not cheaper, it is just later.
Price questions, answered straight
- What is the price of an SMD screen in Pakistan?
- There is no single price, and a figure quoted before the site is known is a guess. The cost is set by pixel pitch, total area, indoor or outdoor construction, the structure that carries the screen and the power protection around it. Send the wall size and the viewing distance on 0320-4119900 (Director) or 0321-9458888 (CEO) and we quote against your actual site.
- Why do two quotes for the same size of screen differ so much?
- Usually because they are not describing the same screen. Pixel pitch alone changes the number of LEDs several times over for the same area, and one quotation may include the structure, power protection and commissioning while another leaves them out. Ask every supplier to state the pitch, the brightness, the module manufacturer and what is excluded, in writing.
- Is SMD screen price calculated per square foot?
- For mid-range installations, yes: the screen is quoted per square foot, with structure, power protection and commissioning itemised separately. High-end installations are quoted as one price for the whole solution, because at that level the screen is the smaller part of the engineering.
- Is an outdoor SMD screen more expensive than an indoor one?
- They are priced on different things. An outdoor screen needs weatherproof cabinets, far higher brightness and a structure engineered for wind load. An indoor screen is usually viewed from closer, so it needs a finer pixel pitch, which means more LEDs in the same area. Either can be the more expensive, depending on the pitch and the structure.
- Which pixel pitch gives the best value?
- The coarsest pitch that still looks sharp from where your closest viewer stands. Paying for a finer pitch than the viewing distance needs is money spent on detail nobody can resolve. We specify it from a site survey, not from a catalogue.
- What is not included in a typical SMD screen quotation?
- This is the question to ask every supplier. Steel or civil work for the structure, power stabilisation, the video processor, transport and work at height are the usual omissions. Our quotations list them up front rather than adding them after the order.
Send us the wall
we will send the number
Wall size, viewing distance and a photo of the location are enough to start.
WHERE WE WORK
Not sure which pixel pitch your space needs? Read the room walks through ten pitches from P0.9 to P10 and what each one is built for. Read the FAQ. For the finest indoor walls, see COB LED displays. Asking about cost? SMD screen price in Pakistan. Renting for an event? LED screen rental, or a single freestanding screen in Lahore: digital standee rental. Or read what we cover after the install.